src/SketchPlugin/Test/TestTrimLine02.py

   1 from salome.shaper import model
   2
   3 from ModelAPI import *
   4 from GeomDataAPI import *
   5 from ModelGeomAlgo import ModelGeomAlgo_Point2D
   6 from salome.shaper import geom
   7 import math
   8
   9 TOLERANCE = 1.e-7
  10
  11 SketchLineId = 'SketchLine'
  12 SketchConstraintCoincidenceId = 'SketchConstraintCoincidence'
  13
  14 aSession = ModelAPI_Session.get()
  15 model.begin()
  16 partSet = model.moduleDocument()
  17 Part = model.addPart(partSet)
  18 Part_doc = Part.document()
  19
  20 # Test1:begin split on arc with coincident point and intersection line : smaller part
  21 Sketch = model.addSketch(Part_doc, model.defaultPlane("XOZ"))
  22 # Test of inverted Arc
  23 SketchLine_1 = Sketch.addLine(10, 80, 40, 10)
  24 SketchLine_2 = Sketch.addLine(40, 10, 70, 80)
  25 SketchLine_3 = Sketch.addLine(70, 80, 100, 10)
  26 SketchLine_4 = Sketch.addLine(100, 10, 130, 80)
  27
  28 SketchLine_intersecting = Sketch.addLine(10, 50, 130, 50)
  29
  30 SketchConstraintCoincidence_1_1 = Sketch.setCoincident(SketchLine_1.endPoint(), SketchLine_2.startPoint())
  31 SketchConstraintCoincidence_1_2 = Sketch.setCoincident(SketchLine_2.endPoint(), SketchLine_3.startPoint())
  32 SketchConstraintCoincidence_1_3 = Sketch.setCoincident(SketchLine_3.endPoint(), SketchLine_4.startPoint())
  33
  34 GeomPoint = geom.Pnt2d(40, 50)
  35
  36 #check number of features before trim
  37 #Sketch_feature = featureToCompositeFeature(Sketch.feature())
  38 #idList_before = []
  39 #for index in range(Sketch_feature.numberOfSubs()):
  40 #  idList_before.append(Sketch_feature.subFeature(index).getKind())
  41
  42 #assert(idList_before.count(SketchLineId) == 3)
  43 #assert(idList_before.count(SketchConstraintCoincidenceId) == 2)
  44
  45 #perform trim
  46 SketchTrim = Sketch.addTrim(SketchLine_intersecting, GeomPoint)
  47 SketchTrim.execute()
  48 model.do()
  49
  50 #check number of features after trim
  51 #SketchFeatures = featureToCompositeFeature(Sketch.feature())
  52 #idList_after = []
  53 #for SubIndex in range(SketchFeatures.numberOfSubs()):
  54 #    SubFeature = SketchFeatures.subFeature(SubIndex)
  55 #    idList_after.append(SubFeature.getKind())
  56
  57 #assert(idList_after.count(SketchLineId) == 3)
  58 #assert(idList_after.count(SketchConstraintCoincidenceId) == 2)
  59
  60 #check if line points are the same
  61 #assert(SketchLine_1.startPoint().x() == 200)
  62 #assert(SketchLine_1.startPoint().y() == 20)
  63 #assert(SketchLine_1.endPoint().x() == 20)
  64 #assert(SketchLine_1.endPoint().y() == 70)
  65
  66 #assert(SketchLine_3.startPoint().x() == -10)
  67 #assert(SketchLine_3.startPoint().y() == 190)
  68 #assert(SketchLine_3.endPoint().x() == 90)
  69 #assert(SketchLine_3.endPoint().y() == 50)
  70
  71 model.end()
  72
  73 #assert(model.checkPythonDump())